Get the facts on installing fire alarms
Our guest columnist casts an expert eye over some of the ways to avoid undue strain on cables, as well as delving deeper into the requirements of BS 7671
Those of you familiar with BS 7671 will know that it says that wiring systems must be selected and erected to avoid during installation, use and maintenance, damage to the sheath or insulation of cables and their terminations (Regulation 522.8.1).
To ensure the requirements of this regulation are met, cables not installed in conduit or trunking are typically supported using a range of clips, saddles, band, glands and ties.
Requirements
All cables and conductors must be supported in such a way that the level of mechanical strain which naturally exists will not cause either the cable/conductor or the terminations to be compromised (522.8.5).
Furthermore, all cable supports and enclosures shall not have sharp edges liable to damage the wiring system, and cable/conductors are not to be damaged by the means of fixing (522.8.11 and 522.8.12).
It is important, therefore, that care is taken when selecting for use supports that are appropriate for the cable/conductors.
Types of support
There is a wide range of options available for the contractor when selecting cable supports. These include among other things:
Cable ties
Cable cleats
Cable clips
Cable tie accessories
Cable glands.
The type of fixing will depend on the nature of the surface to which the support is fixed. For example, cable ties would be suitable for fixing cables installed on basket tray or cable tray, whereas cable clips would be suitable for wooden surfaces. Similarly, the type of support will depend on the type of cable being installed. For example, cable cleats will be suitable for steel-wire armoured cables.
Guidance
The guidance issued within the On-Site Guide (OSG) published by the IET is helpful in deciding on the nature of cable support and the distances recommended between clips.
Appendix D covers cables generally, specific applications such as caravans and the like, overhead wiring as well as conduit and trunking support.
Table D1 details spacings of supports for cables in accessible positions.
Figure 1 on the opposite page gives an example of the recommended distance between clips for a cable having a diameter not exceeding 9mm based on Table D1. As the cable diameter increases, the distance between clips is permitted to grow.
While the support distances are important, it remains the case that the purpose of cable supports is to ensure there is no undue strain on the cable or its terminations.
Similarly, when cables are bent it is important there is no undue strain on the internal conductors caused when the bend is too tight (522.8.3).
Figure 2, pictured above, shows an example of the recommended bending radius for 1.5mm2 insulated and sheathed twin and earth (Table D5 OSG).
Cable entry
Two issues must be addressed when cables enter an accessory – the risk of damage to the sheath or insulation at the point of entry, and any potential strain on connections.
Where a cable enters a metallic accessory box having no protection from sharp edges, there is a risk that the insulation surrounding conductors may become damaged leading to arc and shock risk. Where cables enter a metallic accessory box, it is important that protection is provided, such as with rubber grommets or similar.
Even where cables entering an accessory box or other metallic enclosure are protected from damage, terminations may still be impacted by strain as cables are left unsupported. In such circumstances it is necessary for suitable support to be provided and compression glands provided to ensure the electrical and mechanical strength of terminations (522.8.5 and Note).
Conclusion
All cables and conductors must be suitably supported to ensure that no undue strain exists on the cable or the terminations (522.8). Care should be taken to select appropriate support – e.g. clips, glands and the like – for cables. Unicrimp has a range of such products to help the contractor in carrying out their duties. Find out more at www.unicrimp.com
The Scolmore Group incorporates Click, OVIA, ESP, Sangamo and Unicrimp. As one of the UK’s leading manufacturers of products and solutions for the electrical industry, it has been designing, developing and manufacturing an ever-expanding product range for more than 30 years, including electrical accessories, lighting, home automation, security and cable accessory solutions. Find out more at www.scolmore.com
Figures 1 and 2 courtesy of TJ Bratley
Upgrade your sound system with a 3.5mm male to male stereo audio aux cable for clear and reliable audio.